产品详情
标准:
符合GB BCu80AgP
相当 AWS BCuP-5
说明:
L204是含15%银的磷铜钎料,由于银的加入,提高了强度减少脆性,使钎料熔点降低,其接头强度、塑性、导电性及漫流性是磷铜钎料中最好的一种,对接头的准备及装配相对来说要求较低。
L204 is a copper-phosphorus solder containing 15% silver. Due to the addition of silver, it increases the strength, reduces brittleness, and lowers the melting point of the solder. Its joint strength, plasticity, conductivity and diffusion are the best among copper-phosphorus solders. Kind of relatively low requirements for the preparation and assembly of the joint.
用途:
适用于钎焊铜及铜合金、银、钼等金属。多数用来钎焊冲击振动负载较小的工件,以电机制造工业使用最广。
Suitable for brazing copper and copper alloys, silver, molybdenum and other metals. Most of them are used to braze workpieces with small shock and vibration loads, and are most widely used in the motor manufacturing industry.
钎料化学成分(%)
| P | Ag | Cu |
| 4.8~5.2 | 14.5~15.5 | 余量 |
钎料熔化温度(℃)
| 固相线 | 液相线 |
| 643 | 705 |
供应规格(mm):
| 焊丝直径Φ (长度:500) |
1.2 | 1.6 | 2.0 | 2.4 | 3.0 | 4.0 | 5.0 | 6.0 |
| 扁丝 | 1.3×3.2 | |||||||
注意事项:
1. 钎焊前必须严格清除钎焊处及钎料表面的油脂、氧化物等污物。
2.钎焊铜时不需用钎焊熔剂,但钎焊铜合金必须配钎焊熔剂。
3.钎料的漫流性可凭借母材予热及钎焊温度的高低来适当调节。
1. Before brazing, the grease, oxides and other dirt on the brazing part and the surface of the solder must be strictly removed.
2. Brazing flux is not required when brazing copper, but brazing flux must be used for brazing copper alloys.
3. The flowability of the brazing filler metal can be adjusted appropriately by the preheating of the base material and the brazing temperature.
合作意向表
如您有任何形式的合作意向,欢迎在此留下您的信息,我们将很快与您联络。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。