产品详情
标准:
符合GBSCu656
相当AWS ERCuSi-A
说明:
S211是含少量锰的硅青铜焊丝。熔点约为910~1025℃,塑性好。由于锰的加入,焊接后具有良好的力学性能、抗腐蚀性能和耐磨性能。具有良好的工艺性能。
S211 is a silicon bronze welding wire with a small amount of manganese. The melting point is about 910~1025℃, and the plasticity is good. Due to the addition of manganese, it has good mechanical properties, corrosion resistance and wear resistance after welding. Has good process performance.
用途:
用于硅青铜、紫铜、黄铜及铝青铜的氩弧焊,也可用于铜和铸铁的氩弧焊及堆焊,铜与钢的焊接。如汽车门框、摩托车零件的氩弧钎焊,机车车辆、重型机器摩擦面的堆焊。
It is used for argon arc welding of silicon bronze, red copper, brass and aluminum bronze. It can also be used for argon arc welding and surfacing welding of copper and cast iron, and the welding of copper and steel. Such as argon arc brazing of automobile door frames and motorcycle parts, and surfacing of friction surfaces of locomotives and heavy machinery.
焊丝化学成分:
| Si | Mn | Cu |
| 2.8~4.0 | 0.5~1.5 | 余量 |
供应规格(mm):
| 盘装Φ | 0.6 | 0.8 | 0.9 | 1.0 | 1.2 | 10.5 | |
| 焊丝直径Φ (长度1000) |
1.5 | 2.0 | 2.5 | 3.0 | 4.0 | 5.0 | 6.0 |
注意事项:
1. 焊前必须清除工件焊接边缘及焊丝表面的氧化物、杂质等。
2. 焊接接头板厚小于3mm时,不开坡口;板厚为3~10mm时,开60°~70°V型坡口;板厚大于10mm时,开60°~70°X型坡口。
3. 推荐TIG焊采用直流正极性或交流,MIG焊采用直流反极性,为了避免出现热裂纹,层间温度最好控制在65℃以下。
1. The oxides and impurities on the welding edge of the workpiece and the surface of the welding wire must be removed before welding.
2. When the plate thickness of the welded joint is less than 3mm, no groove; when the plate thickness is 3~10mm, open a 60°~70°V groove; when the plate thickness is greater than 10mm, open a 60°~70°X groove .
3. It is recommended to use DC positive polarity or AC for TIG welding, and DC reverse polarity for MIG welding. In order to avoid thermal cracks, the temperature between layers should be controlled below 65℃.
合作意向表
如您有任何形式的合作意向,欢迎在此留下您的信息,我们将很快与您联络。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。