S201 紫铜氩弧焊丝

铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

产品详情


标准:

GB SCu1898

相当AWS ERCu

说明:

S201是含有少量硅、锰、磷等脱氧元素的特制紫铜焊丝。加入锡改善了熔融铜的流动性。具有焊接工艺性能优良、焊缝成型良好、机械性能高、抗裂性好等优点。

S201 is a special red copper welding wire containing a small amount of deoxidizing elements such as silicon, manganese, and phosphorus. The addition of tin improves the fluidity of molten copper. It has the advantages of excellent welding process performance, good weld formation, high mechanical properties, and good crack resistance.

用途:

用于紫铜氩弧焊及氧-乙炔气焊时作为填充材料。

Used as a filling material for argon arc welding of red copper and oxygen-acetylene gas welding.

焊丝化学成分:

Mn Si Sn P Cu
0.2~0.5 0.2~0.5 0.5~1.0 0.02~0.15 余量

供应规格(mm):

盘装Φ 0.6 0.8 0.9 1.0 1.2 10.5  
焊丝直径Φ
(长度1000)
1.5 2.0 2.5 3.0 4.0 5.0 6.0

注意事项:

1. 工件焊接边缘和焊丝表面的氧化物、油等污物在焊接前必须清除干净,否则会引起气孔、夹渣等缺陷,使焊缝性能降低。

2. 对接接头板厚小于3mm时,不开坡口;板厚为3~10mm时,开60°~70°V型坡口;板厚大于10mm时,开60°~70°X型坡口。为避免未焊透,一般不留钝边。

3. 焊前工件必须预热。板厚小于3mm预热温度为150~300℃;板厚大于3mm时,预热温度为350~500℃。

4. 进行TIG焊时用直流正极性焊接,以获得最大的熔透深度。

1. The oxides, oil and other dirt on the welding edge of the workpiece and the surface of the welding wire must be removed before welding, otherwise it will cause defects such as pores and slag inclusions and reduce the performance of the weld.

2. When the plate thickness of the butt joint is less than 3mm, no groove; when the plate thickness is 3~10mm, 60°~70°V groove; when the plate thickness is greater than 10mm, 60°~70°X groove . In order to avoid incomplete welding, generally no blunt edges are left.

3. The workpiece must be preheated before welding. The preheating temperature for plate thickness is less than 3mm is 150~300℃; when the plate thickness is greater than 3mm, the preheating temperature is 350~500℃.

4. When performing TIG welding, use DC positive polarity welding to obtain the maximum penetration depth.


合作意向表

如您有任何形式的合作意向,欢迎在此留下您的信息,我们将很快与您联络。


S201 紫铜氩弧焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

S211 硅青铜焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

S212 低锡磷青铜焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。