产品详情
说明:
S224是含少量硅的黄铜焊丝,熔点约为905℃。硅在熔池表面形成一层致密的氧化膜,减少锌的蒸发和氧化,并有效地防止氢的溶入而造成气孔。
S224 is a brass welding wire with a small amount of silicon, with a melting point of about 905°C. Silicon forms a dense oxide film on the surface of the molten pool, which reduces the evaporation and oxidation of zinc, and effectively prevents the dissolution of hydrogen from causing pores.
用途:
黄铜氧-乙炔气焊及碳弧焊时作为填充材料,也可用于钎焊铜、钢、铜镍合金、灰口铸铁以及镶嵌硬质合金刀具等。
Brass oxygen-acetylene gas welding and carbon arc welding are used as filler materials, and can also be used for brazing copper, steel, copper-nickel alloy, gray cast iron, and inlaid carbide tools.
焊丝化学成分:
| Cu | Si | Zn |
| 61.0~63.0 | 0.3~0.7 | 余量 |
供应规格(mm):
| 盘装Φ | 0.6 | 0.8 | 0.9 | 1.0 | 1.2 | 1.5 | |
|
焊丝直径Φ (长度1000) |
1.5 | 2.0 | 2.5 | 3.0 | 4.0 | 5.0 | 6.0 |
注意事项:
1. 焊前必须仔细清洁焊件被焊部位及焊丝表面 。
2. 焊件一般预热至400~500℃后施焊。氧-乙炔火焰焊时必须配铜气焊熔剂使用。
3. 焊接火焰应采用中性焰或轻微的氧化焰,适当降低焊接的温度。提高焊接速度,尽量减少熔池在高温下的停留时间,以减少锌的蒸发和氧化。
1. Before welding, the welded parts and the surface of the welding wire must be carefully cleaned.
2. The weldment is generally preheated to 400~500℃ before welding. Oxygen-acetylene flame welding must be used with copper gas welding flux.
3. The welding flame should be a neutral flame or a slight oxidizing flame, and the welding temperature should be appropriately reduced. Increase the welding speed and minimize the residence time of the molten pool at high temperatures to reduce the evaporation and oxidation of zinc.
合作意向表
如您有任何形式的合作意向,欢迎在此留下您的信息,我们将很快与您联络。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。