产品详情
标准:
符合GB BCu60ZnSn(Si)
相当JIS ZYCuSn
说明:
S221是含少量锡、硅的特殊黄铜焊丝,熔点约为890℃。锡能提高焊丝的流动性、强度和抗腐蚀性,而硅可有效地抑制锌的蒸发、消除焊缝气孔和得到满意的机械性能。
S221 is a special brass welding wire with a small amount of tin and silicon, and its melting point is about 890°C. Tin can improve the fluidity, strength and corrosion resistance of the welding wire, while silicon can effectively inhibit the evaporation of zinc, eliminate weld pores and obtain satisfactory mechanical properties.
用途:
黄铜氧-乙炔气焊及碳弧焊时,作填充材料使用。也广泛应用于钎焊铜、钢、铜镍合金、灰口铸铁以及镶嵌硬质合金刀具等,用途很广。
It is used as a filler material for brass oxygen-acetylene gas welding and carbon arc welding. It is also widely used in brazing copper, steel, copper-nickel alloy, gray cast iron and inlaid carbide tools, etc., with a wide range of uses.
焊丝化学成分:
| Cu | Sn | Si | Zn |
| 59.0~61.0 | 0.8~1.2 | 0.15~0.35 | 余量 |
供应规格(mm):
| 盘装(包括圈状)Φ | 0.6 | 0.8 | 0.9 | 1.0 | 1.2 | 10.5 | |
|
焊丝直径Φ (长度1000) |
1.5 | 2.0 | 2.5 | 3.0 | 4.0 | 5.0 | 6.0 |
| 带状 | 厚0.2 宽24 | ||||||
| 长粒状 | 3、4、5×3~15 | ||||||
注:也可按客户要求定制成片状及不同尺寸的带状 。
Note: It can also be customized into flakes and ribbons of different sizes according to customer requirements.
注意事项:
1. 焊前必须仔细清洁焊件被焊部位及焊丝表面。
2. 焊件一般预热到400~500℃后施焊,氧-乙炔火焰焊时必须配铜气焊熔剂使用。
3. 焊接火焰应采用中性焰或轻微的氧化焰,适当降低焊接温度,提高焊接速度,尽量减少熔池在高温下的停留时间,以减少锌的蒸发和氧化。
1. Before welding, the welded parts and the surface of the welding wire must be carefully cleaned.
2. Welding parts are generally preheated to 400~500℃ and then welded. Oxygen-acetylene flame welding must be used with copper gas welding flux.
3. The welding flame should be a neutral flame or a slight oxidizing flame, reduce the welding temperature appropriately, increase the welding speed, and minimize the residence time of the molten pool at high temperatures to reduce the evaporation and oxidation of zinc.
合作意向表
如您有任何形式的合作意向,欢迎在此留下您的信息,我们将很快与您联络。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。
铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。