Cu227 磷青铜焊条

铜及铜合金焊条用途较广,除了用紫铜焊条焊接紫铜外,目前采用较多的是用青铜焊条来焊接铜及铜合金、铜与钢等。但铜及其合金的弧焊一般较钢困难。这是由于铜及铜合金焊接时易产生金属氧化、元素烧损、以及气孔、裂缝和变形等。另外,铜及其合金的导热性特别高致使焊条在引弧后往往不能使母材熔融,而产生熔滴飞散,故焊接铜及铜合金时该类焊件焊前必须要有合理的预热及用较大的焊接电流、直流反接,短弧垂直。焊后应对焊缝进行适当锤击,以消除应力及细化晶粒。另外,铜及其合金塑性好且不溶解碳,也不与碳化合生成脆硬组织,故铜及铜合金焊条也能用来焊补铸铁。

产品详情


标准:

符合GB ECuSn-B

相当AWS ECuSn-C

说明:

Cu227是以锡磷青铜为焊芯,药皮为低氢型的铜合金焊条。有一定的强度、良好的塑性、耐冲击性、耐磨性及耐蚀性能。其特点是焊接工艺性能良好,通用性大。采用直流电源,焊条接正极(直流反接)。

Cu227 is a copper alloy electrode with tin-phosphorus bronze as the core and low-hydrogen type copper alloy coating. It has certain strength, good plasticity, impact resistance, wear resistance and corrosion resistance. It is characterized by good welding process performance and great versatility. Using DC power supply, the electrode is connected to the positive pole (DC reverse connection).

用途:

In addition to welding pure copper, brass, phosphor bronze equivalent and dissimilar metals, it can also be widely used for surfacing phosphor bronze bushings, ship propeller blades, etc., and can also be used for welding repair and surfacing of cast iron.

熔敷金属化学成分(%)

SnPCu
7.0~9.00.05~0.3余量

熔敷金属力学性能

实验项目σb
(MPa)
δ5
(%)
硬度
(HV)
保证值≥270≥1280~115

参考电流:AC或DC

焊条直径(mm)3.24.05.0
焊接电流(A)90~120110~160150~200

注意事项:

1. 焊前焊条须经200℃烘焙一小时。

2. 焊件表面的水分、油污、氧化物等杂质必须清除干净,方可施焊。

3. 焊前预热温度,磷青铜为150~250℃,纯铜约为450℃,碳钢约为200℃。

4. 焊接时宜短弧,多层焊时必须彻底清除层间的熔渣。焊后即用平头锤锤击焊缝,细化晶粒,消除应力。

1. The electrode must be baked at 200°C for one hour before welding.

2. Impurities such as moisture, oil stains and oxides on the surface of the weldment must be removed before welding.

3. The preheating temperature before welding is 150~250℃ for phosphor bronze, 450℃ for pure copper, and 200℃ for carbon steel.

4. Short arc should be used during welding, and the slag between layers must be completely removed during multi-layer welding. After welding, use a flat-head hammer to hammer the weld to refine the grains and eliminate stress.


合作意向表

如您有任何形式的合作意向,欢迎在此留下您的信息,我们将很快与您联络。


S201 紫铜氩弧焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

S211 硅青铜焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

S212 低锡磷青铜焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。