Cu107 紫铜焊条

铜及铜合金焊条用途较广,除了用紫铜焊条焊接紫铜外,目前采用较多的是用青铜焊条来焊接铜及铜合金、铜与钢等。但铜及其合金的弧焊一般较钢困难。这是由于铜及铜合金焊接时易产生金属氧化、元素烧损、以及气孔、裂缝和变形等。另外,铜及其合金的导热性特别高致使焊条在引弧后往往不能使母材熔融,而产生熔滴飞散,故焊接铜及铜合金时该类焊件焊前必须要有合理的预热及用较大的焊接电流、直流反接,短弧垂直。焊后应对焊缝进行适当锤击,以消除应力及细化晶粒。另外,铜及其合金塑性好且不溶解碳,也不与碳化合生成脆硬组织,故铜及铜合金焊条也能用来焊补铸铁。

产品详情


标准:

符合GB ECu

相当AWS ECu

说明:

Cu107是以纯铜为焊芯,低氢型药皮的纯铜焊条。力学性能较好,对大气和海水有良好的耐蚀性。紫铜焊接用,不宜焊接含氧铜及电解铜。采用直流电源,焊条接正极(直流反接)。

Cu107 is a pure copper electrode with pure copper as the core and low-hydrogen coating. It has good mechanical properties and good corrosion resistance to the atmosphere and sea water. For red copper welding, it is not suitable for welding oxygen-containing copper and electrolytic copper. Using DC power supply, the electrode is connected to the positive pole (DC reverse connection).

用途:

主要用来焊接导电铜排,铜制热交换器,船舶用的海水导管等铜构件,也可用于耐海水腐蚀的碳钢零件的堆焊。

It is mainly used for welding conductive copper bars, copper heat exchangers, seawater pipes for ships and other copper components. It can also be used for surfacing welding of seawater corrosion-resistant carbon steel parts.

熔敷金属化学成分(%)

SiMnCu
≤0.5≤0.5≥99.0

熔敷金属力学性能

实验项目σb
(MPa)

冷弯(度)
(D=2t)

保证值≥170≥120

参考电流:AC或DC

焊条直径(mm)3.24.05.0
焊接电流(A)120~140150~170180~200

注意事项:

1. 焊前焊条须在200℃左右烘焙1h。焊件表面的水份、油污、氧化物等杂质必须清除。

2. 由于铜的导热性,被焊母材的预热温度一般比较高,通常在500℃以上。焊接电流的大小应与母材的预热温度相适应。施焊时宜采用垂直短弧、快速,可作往复直线运动,以改善焊缝的成形。

3. 对于较长的焊缝应采用逐步退焊法,焊接速度应尽可能快。多层焊时必须彻底清除层间的熔渣。焊后用平头锤锤击焊缝,消除应力,改善焊缝质量。

1. The electrode must be baked at about 200℃ for 1h before welding. Impurities such as moisture, oil stains and oxides on the surface of the weldment must be removed.

2. Due to the thermal conductivity of copper, the preheating temperature of the base material to be welded is generally higher, usually above 500°C. The size of the welding current should be compatible with the preheating temperature of the base metal. It is advisable to use a vertical short arc, fast, and reciprocating linear motion when welding to improve the shape of the weld.

3. For longer welds, the gradual back welding method should be used, and the welding speed should be as fast as possible. During multi-layer welding, the slag between the layers must be completely removed. After welding, hammer the weld with a flat-head hammer to eliminate stress and improve the quality of the weld.


合作意向表

如您有任何形式的合作意向,欢迎在此留下您的信息,我们将很快与您联络。


S201 紫铜氩弧焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

S211 硅青铜焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

S212 低锡磷青铜焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。