Z508 镍铜铸铁焊条

焊补铸铁用的镍基铸铁焊条在铸铁焊接中属于异质焊缝的冷态焊焊条。药皮为强还原性石墨型,交直流两用,工艺性能良好,可全位置焊接。焊缝金属不存在硬而脆的CFe3(渗碳体)即白口组织,所以焊缝金属具有良好的加工性和承受塑性变形的能力。但熔合区由于母材成分熔化的影响,仍不可避免地会有不同程度的白口组织。为了减轻熔合区硬脆组织对焊后加工性能的不良影响,使其白口层尽量较少,较薄、且不连续,施焊时应该严格遵循冷焊工艺规定操作。另外,某些铸件(如长期在高温、水蒸气中工作的炉栅,锅炉等),因其中的碳已被烧损,铸件具有多空性,变得十分松脆而无法焊、补。

产品详情


标准:

符合GB EZNiCu-1

相当AWS ENiCu-B

说明:

Z508是镍铜合金(蒙乃尔)焊芯,强还原性石墨型药皮的铸铁焊条。可交直流两用,电弧稳定,操作方便。焊缝金属较软但颜色比较亮,收缩率大,抗裂性比较差,焊缝强度也不高,故不宜用于受力部位和对新铸件有色差要求的焊补。为了防止裂缝,对被焊母材推荐采用150~300℃低温预热,以减小焊接应力。

Z508 is a nickel-copper alloy (Monel) core, cast iron electrode with strong reducing graphite coating. It can be used for both AC and DC, with stable arc and convenient operation. The weld metal is soft but the color is brighter, the shrinkage rate is large, the crack resistance is relatively poor, and the weld strength is not high, so it is not suitable for welding repairs on stressed parts and new castings with chromatic aberration requirements. In order to prevent cracks, it is recommended to use 150~300℃ low temperature preheating for the base material to be welded to reduce welding stress.

用途:

常用于强度要求不高的灰口铸铁气孔及砂眼的补焊。

It is often used for repair welding of gray cast iron pores and blisters with low strength requirements.

熔敷金属化学成分(%)

CSiMnNiCuFeS
≤1.0≤0.80≤2.5060.0~70.025.0~35.0≤6.0≤0.025

参考电流:AC或DC

焊条直径(mm)3.24.05.0
焊接电流(A)80~100110~140150~180

注意事项:

1. 首先清除焊接部位的油污、砂、水、锈等污物,并视缺陷类型,开坡口、打止裂孔及熔池造型等准备措施。

2. 如填补大的空隙,应先从四周开始堆焊一层,然后向中部逐步填满。

3. 为避免母材熔化过多,减少白口层。施焊中,尽量采用小电流,短弧,窄道,短道,分散分段焊,每段焊道长度一般不超过50mm,待温度降至不烫手时再继续施焊。并且施焊后立即锤击焊缝以松驰应力防止裂纹。

4. 施焊前应将焊条在150℃左右烘焙一小时。

1. First, remove oil, sand, water, rust and other contaminants from the welding part, and prepare measures such as beveling, cracking prevention, and molten pool modeling depending on the type of defect.

2. To fill a large gap, start from the surrounding area by surfacing one layer, and then gradually fill it up to the middle.

3. In order to avoid excessive melting of the base material, reduce the white mouth layer. In welding, try to use small current, short arc, narrow track, short track, dispersed segment welding, the length of each segment of the weld generally does not exceed 50mm, and continue welding when the temperature drops to not hot. And immediately after welding, hammer the weld to relax the stress and prevent cracks.

4. The welding rod should be baked at about 150℃ for one hour before welding.


合作意向表

如您有任何形式的合作意向,欢迎在此留下您的信息,我们将很快与您联络。


S201 紫铜氩弧焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

S211 硅青铜焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

S212 低锡磷青铜焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。