Z308 纯镍铸铁焊条

焊补铸铁用的镍基铸铁焊条在铸铁焊接中属于异质焊缝的冷态焊焊条。药皮为强还原性石墨型,交直流两用,工艺性能良好,可全位置焊接。焊缝金属不存在硬而脆的CFe3(渗碳体)即白口组织,所以焊缝金属具有良好的加工性和承受塑性变形的能力。但熔合区由于母材成分熔化的影响,仍不可避免地会有不同程度的白口组织。为了减轻熔合区硬脆组织对焊后加工性能的不良影响,使其白口层尽量较少,较薄、且不连续,施焊时应该严格遵循冷焊工艺规定操作。另外,某些铸件(如长期在高温、水蒸气中工作的炉栅,锅炉等),因其中的碳已被烧损,铸件具有多空性,变得十分松脆而无法焊、补。

产品详情


标准:

符合 GB EZNi-1

相当 AWS ENi-CI

说明:

Z308是纯镍焊芯,强还原性石墨型药皮的铸铁焊条,可交直流两用。施焊时电弧稳定,操作方便,焊件可不预热,其是铸铁冷焊焊条中,抗裂性、切削加工性、焊缝强度等综合性能较好的一种焊条。

Z308 is a cast iron electrode with a pure nickel core and a strong reducing graphite coating. It can be used for both AC and DC. When welding, the arc is stable, the operation is convenient, and the weldment can be preheated. It is an electrode with better comprehensive performance such as crack resistance, machinability, and weld strength among cast iron cold welding electrodes.

用途:

可用于常温或稍经预热(至200℃左右)的重要灰口铸铁,如:铸铁薄件的加工面,汽缸盖、发动机座、齿轮箱以及机床导轨、铸铁制成的机械零件等的焊、补。

It can be used for the welding of important gray cast irons at room temperature or slightly preheated (to about 200°C), such as: the machined surface of thin cast iron, cylinder heads, engine seats, gear boxes, machine tool guides, mechanical parts made of cast iron, etc. , Make up.

熔敷金属化学成分(%)

CSiMnFeNiS
≤2.0≤2.5≤1.0≤8.0≥90≤0.03

参考电流:AC或DC

焊条直径(mm)2.53.24.05.0
焊接电流(A)50~8080~100110~140150~180

注意事项:

1. 首先清除焊接部位的油污、砂、水、锈等污物,并视缺陷类型,开坡口、打止裂孔及熔池造型等准备措施。

2. 如填补大的空隙,应先从四周开始堆焊一层,然后向中部逐步填满。

3. 为避免母材熔化过多,减少白口层。施焊中,尽量采用小电流,短弧,窄道,短道,分散分段焊,每段焊道长度一般不超过50mm,待温度降至不烫手时再继续施焊。并且施焊后立即锤击焊缝以松驰应力防止裂纹。

4. 施焊前应将焊条在150℃左右烘焙一小时。

1. First, remove oil, sand, water, rust and other contaminants from the welding part, and prepare measures such as beveling, cracking prevention, and molten pool modeling depending on the type of defect.

2. To fill a large gap, start from the surrounding area by surfacing one layer, and then gradually fill it up to the middle.

3. In order to avoid excessive melting of the base material, reduce the white mouth layer. In welding, try to use small current, short arc, narrow track, short track, dispersed segment welding, the length of each segment of the weld generally does not exceed 50mm, and continue welding when the temperature drops to not hot. And immediately after welding, hammer the weld to relax the stress and prevent cracks.

4. The welding rod should be baked at about 150℃ for one hour before welding.


合作意向表

如您有任何形式的合作意向,欢迎在此留下您的信息,我们将很快与您联络。


S201 紫铜氩弧焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

S211 硅青铜焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。

S212 低锡磷青铜焊丝


铜及铜合金焊丝常用于焊接铜及铜合金,其中黄铜焊丝也广泛用于钎焊碳钢、铸铁及硬质合金刀具等。选用适当的焊丝进行氩弧焊是保证铜及青铜焊接质量的有效方法之一,不但可获得性能良好的焊缝而且有利于减少焊件变形。用氧-乙炔气焊时应配合铜气焊熔剂使用,或使用已包有铜气焊熔剂的铜焊丝。碳弧焊也是焊接铜及铜合金的常用方法之一,碳弧焊的焊接工艺和气焊类似,焊丝及熔剂也和气焊时一样。